Klein-tools MM1300 Bedienungsanleitung PDF herunterladen (Seite 2)

ENGLISH

FEATURE DETAILS

MM1300

Instruction Manual

GENERAL SPECIFICATIONS

The Klein Tools MM1300 is an auto-ranging multimeter. It measures AC/DC

voltage, AC/DC current, resistance, capacitance, frequency, duty cycle, and

temperature. It can also test diodes and continuity.

• Operating Altitude: 6572 ft / 2000m

• Relative Humidity: <75%

• Operating Temperature: 32°F to 122°F (0°C to 50°C)

• Storage temperature: -4°F to 140°F (-20°C to 60°C) <80% R.H.

• Accuracy Temperature: 64°F to 82°F (18°C to 28°C)

• Temperature Coefcient: 0.1*(specified accuracy)/ °C

• Sampling Frequency: 3 samples per second

• Dimensions: 7" x 3.5" x 1.9" (178 mm x 89 mm x 229 mm)

• Weight: 14 oz. (28 g)

• Calibration: Accurate for one year

• Safety Rating: CAT III 1000V, CAT IV 600V

• Accuracy: ± (% of reading + # of least significant digits)

WARNINGS

To ensure safe operation and service of the tester, follow these instructions.

Failure to observe theses warnings can result in severe injury or death.

• Before each use, verify meter operation by measuring a known

voltage or current.

• Never use the meter on a circuit with voltages that exceed the

category based rating of this meter.

• Do not use the meter during electrical storms, or in wet weather.

• Do not use the meter or test leads if they appear to be damaged.

• Ensure meter leads are fully seated, and keep fingers away from the

metal probe contacts when making measurements.

• Do not open the meter to replace batteries or fuses while the probes

are connected.

• Use caution when working with voltages above 60V DC, or 25V AC

RMS. Such voltages pose a shock hazard.

• To avoid false readings that can lead to electrical shock, replace

batteries if a low battery indicator appears.

• Unless measuring voltage or current, shut off and lock out power

before measuring resistance or capacitance.

• Always adhere to local and national safety codes. Use individual

protective equipment to prevent shock and arc blast injury where

hazardous live conductors are exposed.

SYMBOLS

AC Alternating Current Warning or Caution

DC Direct Current Dangerous levels

DC/AC Voltage or Current Double Insulated Class II

Ground AC Source

Do not attempt to measure more than 1000V.

Do not attempt to measure more than 400mA.

Do not attempt to measure more than 10A.

D. Auto Power-Off (Apo)

• Device will power off after 30 minutes non-use.

• Press the select button to wake.

• Disabled during Max/Min function.

• Holding Select button while turning on disables Auto Power-Off.

E. Select Functionality Button

• Switch between AC and DC.

• Switch between “”, “

” and “ ”.

• Switch between Hz and %.

• Switch between °F and °C.

• Wake meter during Auto Power Off.

F. Relative Reading Mode

• Press to store current value.

• Display will now show the difference between the stored and live

readings.

• Press again to return to live reading.

G. Auto / Manual Range

• Press repeatedly to cycle through manual ranges.

• Press for 2 seconds to return to auto ranging mode.

• AT is displayed on LCD only during auto ranging mode.

H. Max/Min Hold

• Press to enter Max/Min mode; the largest and smallest values will

be saved while in this mode.

• Press repeatedly to alternative between the maximum and

minimum readings.

• Press for 2 seconds to return to live reading and clear the stored

maximum and minimum values.

I. Hold / Auto Hold / Backlight

• Hold captures the current displayed value.

• Auto Hold captures the first stable displayed value, until a new

stable value is measured. The meter will then capture the new value

and emit a beep (V, Ohm, Temperature and Amp functions).

• Press to hold current input on the display.

• Press again to enter Auto-Hold to capture stable values.

• Press again to return to normal operation.

• Press and hold to activate display backlight.

• Using lights drains the battery significantly.

J. K. Battery/Fuse Replacement

• When indicator is displayed on the LCD, batteries must be

replaced.

• Remove rubber boot, back screw and replace 2 x AAA batteries.

• This meter uses 440mA/1000V (69192) and 11A/1000V (69191)

fast blow fuses.

L. Magnetic Hanger Accessory (Optional, Sold Separately)

• Slide magnetic adapter into protective rubber boot.

• Attach instruments to metal for hands-free use.

M. Bar Graph

• The bar graph shows an approximate analog representation

of a measurement.

•

The bar graph responds much faster than the digital display.

• The scale of the bar graph is zero to the maximum reading of

the selected range.

FUNCTION INSTRUCTIONS

1. AC Voltage: <1000V.

Features:

Do not attempt to measure more than 1000V

• Rotate selector to "AC" Voltage position.

• Attach red lead to “V” input.

3. AC/DC Current (large): <10A

Features:

Do not attempt to measure more than 10A

• Start with this setting if current level is unknown.

• Meter will automatically select "A" when red lead is connected to

"A" input. “LEAd” will show if connected but fuse is blown.

4. AC/DC Current (small): < 400mA

Features:

Do not attempt to measure more than 400mA

• Rotate selector to "µA" or "mA" position

• Attach red lead to “mAμA” input.

• Select AC or DC current source.

5. Resistance/Diode/Continuity

Continuity Features:

MAX/MINHOLD

• Display shows resistance.

• Buzzer sounds if less than 40Ω

Diode Features:

MAX/MINHOLD

Display shows:

• Forward voltage drop if forward

biased.

• “O.L” if reverse biased.

Resistance Features:

•

Do not measure resistance on a

live circuit.

•  = < 60MΩ

HOLDREL

RANGE MAX/MIN

2. DC Voltage: <1000V.

Features:

Do not attempt to measure more than 1000V

• Rotate selector to "DC" Voltage position.

• Attach red lead to “V” input.

MAX/MINRANGEHOLDREL

A- HOLD

MAX/MINRANGEHOLDREL

A- HOLD

MAX/MINRANGEHOLDREL

A- HOLD

MAX/MINRANGEHOLDREL

A- HOLD

PRESS TO SELECT

Resistance

Diode

Continuity

Dwg Name: MM1300-139713ART Dwg No: 139713

ECO No: 16082 Pkg Dwg Ref: 1650 Rev: B

Color Reference: N/A

PRESS

MM1300 Instruction Manuals - MASTER.indd 5-8 3/12/2014 10:16:57 AM

1 2 3 4 5 6 7 8

Kommentare zu diesen Handbüchern

Keine Kommentare

Klein-tools MM1300 Bedienungsanleitung Seite 2

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Messgeräte Klein-tools MM1300